Shopping cart is empty
0 item(s) in your shopping cart
Search Our Catalog
Listing By Manufacturer
Used & Refurbished



Airbrush & Paint


Air System Products->


Batteries & Regulators->

Camera & FPV

Cars and Surface

CG Stands


Cleaners and Polish

Cockpit Accessories

Composite Materials

Electric Power->


Festo Fittings

Flight Box & Field

Flight Simulation

Fuel System->

Hardware & Linkage

Hinges & Horns

Landing Gear->




PISCO Fittings

Pipes & Nozzles


Power Distribution Systems->

Radio Equipment->

Servo Leads->

Servo Mounts & Arms

SMC Fittings

Smoke Systems



Thermal Protection

Tools & Supplies


Turbine Engines->
|__AMT Netherlands
|__KingTech Accessories
|__Misc Engine Accessories

Turbine Engine Mounts

Turbine Oil

UAV & Drone

UltraCote, Decals & Graphics

Wheels & Brakes->

Wire & Connectors

Gift Certificates

Gift Suggestions

View All Products ->

All Products sorted by Categories ->

All Products sorted by Manufacturers ->
JetCat Jetnet FOD Screen, P200  Product 92 of 92 in category JETCAT ACCESSORIES

JetCat Turbine DMSS Telemetry Module

JetCat Turbine DMSS Telemetry Module
Click to enlarge
Stock status:In Stock
Price $84.99 
Model JRPELE006
Manufacturer JR
Add to Wish List



JR - JRPELE006 - JetCat Turbine DMSS Telemetry Module

Manufactured for by MacGregor Industries Ltd. UK.

This telemetry unit will take data from your JetCat ECU and relay it to your JR DMSS radio. Please note that the data which is relayed back to your radio may not be 100% accurate and should be used as a guide.

Please plug the supplied JetCat style lead into the telemetry device and either the data port on your JetCat ECU or the plug on the I/O board. Then plug the supplied male-male patch lead into the other end of the telemetry device noting the polarity with the other end of this lead into either the data port on your JR DMSS receiver or into you TLS1-ADP (sold separately).

You will need to configure the telemetry screen on your JR DMSS radio. Please refer to the radios manual on how to do this.

Several different turbine parameters can be monitored including;
Parameter Radio Telemetry Setting
Turbine RPM  RPM
Turbine Exhaust Gas Temperature (EGT)  Temp
Turbine Status  FPACK Watts*
Last Shutdown Code  FPACK Watts*
EUC Battery Voltage  FPACK Voltage
Current Fuel Flow  FPACK Current
MI Consumed/Remaining  FPACK.mah**

* Please see the table below for status and shutdown codes

** The fuel tank size will need to be configured on both the transmitter and the ECU. For the transmitter set the battery capacity to your fuel tank size (measure in ml), for the ECU follow the calibration instructions in the JetCat manual.
Turbine Status

The telemetry unit provides running and shutdown status codes using the FPACK Watts measure. The table below shows the code mappings:
Code Type Meaning
1  Running  Wait for RPM (Standby/Start)
2  Running  Ignite
3  Running  Accelerate
4  Running  Stabilise
5  Running  Learn HI
6  Running  Learn LO
8  Running  Slow Down
10  Running  Auto Off
11  Running  Run (Reg.)
12  Running  Acceleration delay
13  Running  SpeedReg (Speed Ctrl)
14  Running  Two-Shaft-Regulate (Only for Turbines with Secondary Shaft)
15  Running  PreHeat1 (Only for direct Kerosene startup mode)
16  Running  PreHeat2 (Only for direct Kerosene startup mode)
17  Running  MainFStrt (Only for direct Kerosene startup mode)
19  Running  Keros.FullOn(Only for direct Kerosene startup mode)
100  Last Shutdown  No Off-Condition defined
101  Last Shutdown  Shutdown via RC
102  Last Shutdown  Over temperature
103  Last Shutdown  Ignition timeout
104  Last Shutdown  Acceleration timeout
105  Last Shutdown  Acceleration too slow
106  Last Shutdown  Over RPM
107  Last Shutdown  Low RPM Off
108  Last Shutdown  Low Battery
109  Last Shutdown  Auto Off
110  Last Shutdown  Low Temperature Off
111  Last Shutdown  Hi Temperature Off
112  Last Shutdown  Glow Plug defective
113  Last Shutdown  Watch Dog Timer
114  Last Shutdown  Fail Safe Off
115  Last Shutdown  Manual Off (via GSU)
116  Last Shutdown  Power Fail (Battery Fail)
117  Last Shutdown  Temp Sensor Fail (Only during startup)
118  Last Shutdown  Fuel Fail
119  Last Shutdown  Prop Fail (Only two shaft Engines)
120  Last Shutdown  2nd Engine Fail
121  Last Shutdown  2nd Engine differential too high
122  Last Shutdown  2nd Engine no communication


Mfg Info


Manufacturer Info
Other products

Extra Info

There are currently no product reviews
Write a review on this product!

Extra Info
This product was added to our catalog on Friday 22 September, 2017.
Notify me of updates to JetCat Turbine DMSS Telemetry Module
Tell someone you know about this product.
My Account Info
Your Email Address
Your Password
Pay Now - Bill Me Later!
Shipping & Returns
Privacy Policy
Terms & Conditions
Dreamworks Library
New Articles (0)
All Articles (13)
News & Updates (4)
Product Manuals -> (1)
Tips & How-To's (7)
Turbine Service (1)
JetCat Turbine DMSS Telemetry Module

JetCat Turbine DMSS Telemetry Module

Add to cart
more info
Scratch and Dent Jet Pilot Bust with Flight Helmet Style #4

Scratch and Dent Jet Pilot Bust with Flight Helmet Style #4

$42.99  $32.99 
Add to cart
more info
Comments more
Write ReviewWrite a review on this product!