ELECTRIC RETRACTS

ELECTRIC RETRACTS

Pro-Link Sidewinder, Taurus and Hercules Electric Series Retracts by Dreamworks

Dreamworks now offers our popular retract sets in both pneumatic and electric drive options!

Desc

Items 1-9 of 39

View as Grid List
per page
  1. Pro-Drive Gemini Electric Nose Retract
    $150.00
    Pro-Drive Gemini Electric Nose Retract

    Pro-Drive Gemini Electric Nose Retract

    Dreamworks is pleased to present our Pro-Drive electric retract systems. Over a year in development, our new electric series retracts and control modules are the most advanced electric gear systems available.

    All the features of our Taurus Series with modified frames to provide a smaller footprint at the rails.

    Specs:

    •     Length - 4.125" (105mm)
    •     Frame Width - .88" (22.3mm)
    •     Depth - 1.25" (31.75mm)
    •     Frame Rail mount length - 1.75" (44.45mm)
    •     Frame Rail Mount Width - 1.75" (44.45mm)
    •     90 Degree Extension

     

    • Cut Off Amperage - 1.5A
    • Operating Voltage - 6V to 10V
    • 5.25" long 3.1oz strut, weight loaded at the axle - Stall was achieved at 38oz (2.375lbs, 1077g)
    • 8" long 6oz strut, weight loaded at the axle - Stall was achieved at 17.3oz (1.08lbs, 490.44g)
    • Transit time is roughly 6 seconds.
    Learn More
  2. Pro-Link LGC15 Controller and Sequencer for Electric Retracts
    $175.00
    Pro-Link LGC15 Controller and Sequencer for Electric Retracts

     Controller for electric landing gear, brakes and doors.

    -Direct control of 3 motors in bidirectional mode up to 12V/5A. Supports the different motor shut-off control types currently available (time, overcurrent and encoder)

    -Dual control of electric brakes, full proportional, lineal and adjustable pulsed mode.

    -Differential brake mode, to steer the model using the brakes.

    -Steering servo processor. Gain, sense and center can be adjusted. The steering servo is centered during retraction.

    -Internal Gyro. It can be mixed with the steering servo output and mixed to the differential brakes.

    -8 servo outputs for the control of the doors. The endpoints of each servo can be programmed individually. The Servo speed can be programmed independent in the two senses in 0,1s resolution.

    -10 step sequencer. The position of the gears and the position of the 8 doors can be defined independent in each step. Step duration resolution in 0,1s steps.

    -Wide choice of RC inputs. Single RC channel, Dual RC channel, Futaba SBUS, UDI Bus, SRXL Bus, JR Mode A Bus, JETI EX Bus.

    -Programmable trough integrated color touchscreen.

    -uSD card slot to save the settings and upgrade the software

    User's manual: http://www.xicoy.com/LG15.pdf

    Important Note: This controller is set up to be used with Pro-Link Taurus, Hercules, and Genesis Retract systems meaning 2.0 Amp motor cut-off, 9 sec. Time, and .01sec Unload.  If other parameters are needed the controller must be preprogrammed by the manufacturer.

     

    Learn More
  3. Pro-Link GENESIS 40 Electric Retracts 8mm InDirect Steer PRO
    $539.99
    Pro-Link GENESIS 40 Electric Retracts 8mm InDirect Steer PRO

    Pro-Link GENESIS 40 SERIES Electric Retracts 8mm Mains, 8mm Pin InDirect Steer - PRO Controller

    The Genesis Series offers an extremely robust two piece CNC frame, sealing the motor and gearbox from the mechanics while eliminating all possibility of friction or binding due to uneven mounting rails. Over-sized T-Bar, beefed up trunion, and a dual bearing supported drive screw assures these retracts remain slop free even after those not-so-perfect landings. Connector plug is integrated into the retract housing, allowing for simple gear installation and removal.

    One of the most important upgrades to the Genesis Series is position sensing end stops. Travel endpoints are sensor controlled, eliminating all the stresses on the mechanics and drive system associated stall current type actuators. As an additional safety, we retained the stall current mode while gear are in transit. Drive gearing has been specifically selected to provide substantially more torque than our competitors while retaining our quick transit speed.

    We are confident you will find our new Genesis series to be the most sophisticated, robust, and reliable electric retract system available!

    Model Specifications:

    • 8mm Trunion Lock on Main Retracts.
    • 8mm Pin on Nose Retract w/InDirect Steering Setup
    • PL-LGC13 PRO controller, includes brake control and steering servo control and more!

    Features:

    • Machined from solid 7075 aluminum, robust design including 2 ball bearings for long life, smooth running and low friction to increase the torque.
    • Exclusive internal electronic circuit including 2 hall magnetic sensor to detect the endpoints to stop the motor when the end position is reached, saving wear to the mechanical components due at the suppression of the usual end of travel overload often seen in other systems.
    • 4.5s of travel time. Torque of 22 Lb/inch (25kg/cm). (Typical)
    • For up to 36lb plane weight. (16kg)
    • 90º, Normal Operation.
    • Tiller steering.
    • Replaceable connection leads for ease maintenance and installation.
    • Use 6,6V LiFe or 7,4V Lipo. Capable of 15A peak. App. 30mAh used per cycle.
    • Compatible with HV receiver installations (up to 9V).

    PRO Features:

    -Control by Single channel (Gear operation and brake operation combined on single channel) or separate channels for gear and brake.

    -Control 3 landing gears. Programmable independent delay for each gear in UP and DOWN sequence.

    -Control of electric brake:

    •  Proportional and adjustable maximum brake force
    •  Continuous operation or pulsed mode for "ABS" effect, 10 levels of pulse ratio.
    •  Brake Limiter to set max brake force

    -Control of steering servo

    • Allow to use same channel as the rudder despite different center, independant travel gain and direction on steering servo from rudder servo. The steering servo center, travel and sense of movement can be adjusted.
    • The steering servo is centered and deactived during gear operation and gear UP phase.

    -Door control output:

    • 3 independent servo outputs for door control.
    • Each output can be programmed in 3 different positions (Gear UP, Gear Down and Gear Moving phase).
    • Servo Switch-off. Door servos can be deactivated after movement to prevent the posibility of servo burnout on a jammed door. Deactivation time can be programmed.

    -Manual mode:

    • Provides the ability cycle the gear manually for testing during setup phase, movement can be stopped and reasumed in any position.
    • Each drive motor can be independently run in any direction and stopping in any position for checking clearance, etc.

    -Motor Log:

    • Cycle counter for scheduled maintenance.

    -Easy setup:  All adjustments are done through a Xicoy data terminal (not included).

    -Electronic switch for the main battery.

    Note:

    •  The unit can be programmed using the onboard LED and switch like our Basic controller (options limited using this program method)
    •  Data terminal for full programming not included. Compatible with all Xicoy SBus style data terminals used with Xicoy brand ECUS.

    Includes:

    • Two Main Retracts with 1/2" Trunion Lock.
    • One Nose Retract with 8mm Pin.
    • PL-LCG13 PRO Controller.
    • Three Male to Male Leads.
    • MPX Battery Connector.

    Demo Video of GENESIS Retracts installed in Boomerang Turbinator:



     

    Learn More
  4. Pro-Link GENESIS 40 Electric Retracts 8mm Tiller Steer PRO
    $519.00
    Pro-Link GENESIS 40 Electric Retracts 8mm Tiller Steer PRO

    Pro-Link GENESIS 40 SERIES Electric Retracts 8mm Mains, 8mm Pin Tiller Steer - PRO Controller

    The Genesis Series offers an extremely robust two piece CNC frame, sealing the motor and gearbox from the mechanics while eliminating all possibility of friction or binding due to uneven mounting rails. Over-sized T-Bar, beefed up trunion, and a dual bearing supported drive screw assures these retracts remain slop free even after those not-so-perfect landings. Connector plug is integrated into the retract housing, allowing for simple gear installation and removal.

    One of the most important upgrades to the Genesis Series is position sensing end stops. Travel endpoints are sensor controlled, eliminating all the stresses on the mechanics and drive system associated stall current type actuators. As an additional safety, we retained the stall current mode while gear are in transit. Drive gearing has been specifically selected to provide substantially more torque than our competitors while retaining our quick transit speed.

    We are confident you will find our new Genesis series to be the most sophisticated, robust, and reliable electric retract system available!

    Model Specifications:

    • 8mm Trunion Lock on Main Retracts.
    • 8mm Pin on Nose Retract w/Tiller.
    • PL-LGC13 PRO controller, includes brake control and steering servo control and more!

    Features:

    • Machined from solid 7075 aluminum, robust design including 2 ball bearings for long life, smooth running and low friction to increase the torque.
    • Exclusive internal electronic circuit including 2 hall magnetic sensor to detect the endpoints to stop the motor when the end position is reached, saving wear to the mechanical components due at the suppression of the usual end of travel overload often seen in other systems.
    • 4.5s of travel time. Torque of 22 Lb/inch (25kg/cm). (Typical)
    • For up to 36lb plane weight. (16kg)
    • 90º, Normal Operation.
    • Tiller steering.
    • Replaceable connection leads for ease maintenance and installation.
    • Use 6,6V LiFe or 7,4V Lipo. Capable of 15A peak. App. 30mAh used per cycle.
    • Compatible with HV receiver installations (up to 9V).

    PRO Features:

    -Control by Single channel (Gear operation and brake operation combined on single channel) or separate channels for gear and brake.

    -Control 3 landing gears. Programmable independent delay for each gear in UP and DOWN sequence.

    -Control of electric brake:

    •  Proportional and adjustable maximum brake force
    •  Continuous operation or pulsed mode for "ABS" effect, 10 levels of pulse ratio.
    •  Brake Limiter to set max brake force

    -Control of steering servo

    • Allow to use same channel as the rudder despite different center, independant travel gain and direction on steering servo from rudder servo. The steering servo center, travel and sense of movement can be adjusted.
    • The steering servo is centered and deactived during gear operation and gear UP phase.

    -Door control output:

    • 3 independent servo outputs for door control.
    • Each output can be programmed in 3 different positions (Gear UP, Gear Down and Gear Moving phase).
    • Servo Switch-off. Door servos can be deactivated after movement to prevent the posibility of servo burnout on a jammed door. Deactivation time can be programmed.

    -Manual mode:

    • Provides the ability cycle the gear manually for testing during setup phase, movement can be stopped and reasumed in any position.
    • Each drive motor can be independently run in any direction and stopping in any position for checking clearance, etc.

    -Motor Log:

    • Cycle counter for scheduled maintenance.

    -Easy setup:  All adjustments are done through a Xicoy data terminal (not included).

    -Electronic switch for the main battery.

    Note:

    •  The unit can be programmed using the onboard LED and switch like our Basic controller (options limited using this program method)
    •  Data terminal for full programming not included. Compatible with all Xicoy SBus style data terminals used with Xicoy brand ECUS.

    Includes:

    • Two Main Retracts with 1/2" Trunion Lock.
    • One Nose Retract with 8mm Pin.
    • PL-LCG13 PRO Controller.
    • Three Male to Male Leads.
    • MPX Battery Connector.

    Demo Video of GENESIS Retracts installed in Boomerang Turbinator:



     

    Learn More
  5. Pro-Link GENESIS 40 Electric Retracts 8mm InDirect Steer BASIC
    $499.99
    Pro-Link GENESIS 40 Electric Retracts 8mm InDirect Steer BASIC

    Pro-Link GENESIS 40 SERIES Electric Retracts 8mm Mains, 8mm Pin InDirect Steer - BASIC Controller

    The Genesis Series offers an extremely robust two piece CNC frame, sealing the motor and gearbox from the mechanics while eliminating all possibility of friction or binding due to uneven mounting rails. Over-sized T-Bar, beefed up trunion, and a dual bearing supported drive screw assures these retracts remain slop free even after those not-so-perfect landings. Connector plug is integrated into the retract housing, allowing for simple gear installation and removal.

    One of the most important upgrades to the Genesis Series is position sensing end stops. Travel endpoints are sensor controlled, eliminating all the stresses on the mechanics and drive system associated stall current type actuators. As an additional safety, we retained the stall current mode while gear are in transit. Drive gearing has been specifically selected to provide substantially more torque than our competitors while retaining our quick transit speed.

    We are confident you will find our new Genesis series to be the most sophisticated, robust, and reliable electric retract system available!

    Model Specifications:

    • 8mm Trunion Lock on Main Retracts.
    • 8mm Pin on Nose Retract w/InDirect Steering Setup
    • PL-LGC12 Basic controller, includes brake control and steering servo control.

    Features:

    • Machined from solid 7075 aluminum, robust design including 2 ball bearings for long life, smooth running and low friction to increase the torque.
    • Exclusive internal electronic circuit including 2 hall magnetic sensor to detect the endpoints to stop the motor when the end position is reached, saving wear to the mechanical components due at the suppression of the usual end of travel overload often seen in other systems.
    • 4.5s of travel time. Torque of 22 Lb/inch (25kg/cm). (Typical)
    • For up to 36lb plane weight. (16kg)
    • 90º, Normal Operation.
    • InDirect Style steering.
    • Replaceable connection leads for ease maintenance and installation.
    • Use 6,6V LiFe or 7,4V Lipo. Capable of 15A peak. App. 30mAh used per cycle.
    • Compatible with HV receiver installations (up to 9V).


    BASIC Features:

    • Direct control of 3 motors in bidirectional and regulated mode up to 2,5A
    • Control of electric brake, fully proportional, brake deactivation when gear-up
    • Steering servo processor. Servo deactivation with gear-up activation
    • Small size and lightweight.

    Includes:

    • Two Main Retracts with 8mm Trunion Lock.
    • One Nose Retract with 8mm Pin.
    • PL-LCG12 Basic Controller.
    • Three Male to Male Leads.
    • MPX Battery Connector.

    Demo Video of GENESIS Retracts installed in Boomerang Turbinator:

     



     

    Learn More
  6. Pro-Link GENESIS 40 Electric Retracts 1/2" InDirect Steer PRO
    $539.99
    Pro-Link GENESIS 40 Electric Retracts 1/2" InDirect Steer PRO

    Pro-Link GENESIS 40 SERIES Electric Retracts 1/2" Mains, 8mm Pin InDirect Steer - PRO Controller

    The Genesis Series offers an extremely robust two piece CNC frame, sealing the motor and gearbox from the mechanics while eliminating all possibility of friction or binding due to uneven mounting rails. Over-sized T-Bar, beefed up trunion, and a dual bearing supported drive screw assures these retracts remain slop free even after those not-so-perfect landings. Connector plug is integrated into the retract housing, allowing for simple gear installation and removal.

    One of the most important upgrades to the Genesis Series is position sensing end stops. Travel endpoints are sensor controlled, eliminating all the stresses on the mechanics and drive system associated stall current type actuators. As an additional safety, we retained the stall current mode while gear are in transit. Drive gearing has been specifically selected to provide substantially more torque than our competitors while retaining our quick transit speed.

    We are confident you will find our new Genesis series to be the most sophisticated, robust, and reliable electric retract system available!

    Model Specifications:

    • 1/2" Trunion Lock on Main Retracts.
    • 8mm Pin on Nose Retract w/InDirect Steering System
    • PL-LGC13 PRO controller, includes brake control and steering servo control and more!

    Features:

    • Machined from solid 7075 aluminum, robust design including 2 ball bearings for long life, smooth running and low friction to increase the torque.
    • Exclusive internal electronic circuit including 2 hall magnetic sensor to detect the endpoints to stop the motor when the end position is reached, saving wear to the mechanical components due at the suppression of the usual end of travel overload often seen in other systems.
    • 4.5s of travel time. Torque of 22 Lb/inch (25kg/cm). (Typical)
    • For up to 36lb plane weight. (16kg)
    • 90º, Normal Operation.
    • InDirect steering.
    • Replaceable connection leads for ease maintenance and installation.
    • Use 6,6V LiFe or 7,4V Lipo. Capable of 15A peak. App. 30mAh used per cycle.
    • Compatible with HV receiver installations (up to 9V).

    PRO Features:

    -Control by Single channel (Gear operation and brake operation combined on single channel) or separate channels for gear and brake.

    -Control 3 landing gears. Programmable independent delay for each gear in UP and DOWN sequence.

    -Control of electric brake:

    •  Proportional and adjustable maximum brake force
    •  Continuous operation or pulsed mode for "ABS" effect, 10 levels of pulse ratio.
    •  Brake Limiter to set max brake force

    -Control of steering servo

    • Allow to use same channel as the rudder despite different center, independant travel gain and direction on steering servo from rudder servo. The steering servo center, travel and sense of movement can be adjusted.
    • The steering servo is centered and deactived during gear operation and gear UP phase.

    -Door control output:

    • 3 independent servo outputs for door control.
    • Each output can be programmed in 3 different positions (Gear UP, Gear Down and Gear Moving phase).
    • Servo Switch-off. Door servos can be deactivated after movement to prevent the posibility of servo burnout on a jammed door. Deactivation time can be programmed.

    -Manual mode:

    • Provides the ability cycle the gear manually for testing during setup phase, movement can be stopped and reasumed in any position.
    • Each drive motor can be independently run in any direction and stopping in any position for checking clearance, etc.

    -Motor Log:

    • Cycle counter for scheduled maintenance.

    -Easy setup:  All adjustments are done through a Xicoy data terminal (not included).

    -Electronic switch for the main battery.

    Note:

    •  The unit can be programmed using the onboard LED and switch like our Basic controller (options limited using this program method)
    •  Data terminal for full programming not included. Compatible with all Xicoy SBus style data terminals used with Xicoy brand ECUS.

     

    Includes:

    • Two Main Retracts with 1/2" Trunion Lock.
    • One Nose Retract with 8mm Pin.
    • PL-LCG13 PRO Controller.
    • Three Male to Male Leads.
    • MPX Battery Connector.

    Demo Video of GENESIS Retracts installed in Boomerang Turbinator:

     


     

    Learn More
  7. Pro-Link GENESIS 40 Electric Retracts 1/2" InDirect Steer BASIC
    $499.99
    Pro-Link GENESIS 40 Electric Retracts 1/2" InDirect Steer BASIC

    Pro-Link GENESIS 40 SERIES Electric Retracts 1/2" Mains, 8mm Pin InDirect Steer - BASIC Controller

    The Genesis Series offers an extremely robust two piece CNC frame, sealing the motor and gearbox from the mechanics while eliminating all possibility of friction or binding due to uneven mounting rails. Over-sized T-Bar, beefed up trunion, and a dual bearing supported drive screw assures these retracts remain slop free even after those not-so-perfect landings. Connector plug is integrated into the retract housing, allowing for simple gear installation and removal.

    One of the most important upgrades to the Genesis Series is position sensing end stops. Travel endpoints are sensor controlled, eliminating all the stresses on the mechanics and drive system associated stall current type actuators. As an additional safety, we retained the stall current mode while gear are in transit. Drive gearing has been specifically selected to provide substantially more torque than our competitors while retaining our quick transit speed.

    We are confident you will find our new Genesis series to be the most sophisticated, robust, and reliable electric retract system available!

    Model Specifications:

    • 1/2" Trunion Lock on Main Retracts.
    • 8mm Pin on Nose Retract w/InDirect Steering Setup
    • PL-LGC12 Basic controller, includes brake control and steering servo control.

    Features:

    • Machined from solid 7075 aluminum, robust design including 2 ball bearings for long life, smooth running and low friction to increase the torque.
    • Exclusive internal electronic circuit including 2 hall magnetic sensor to detect the endpoints to stop the motor when the end position is reached, saving wear to the mechanical components due at the suppression of the usual end of travel overload often seen in other systems.
    • 4.5s of travel time. Torque of 22 Lb/inch (25kg/cm). (Typical)
    • For up to 36lb plane weight. (16kg)
    • 90º, Normal Operation.
    • InDirect Style steering.
    • Replaceable connection leads for ease maintenance and installation.
    • Use 6,6V LiFe or 7,4V Lipo. Capable of 15A peak. App. 30mAh used per cycle.
    • Compatible with HV receiver installations (up to 9V).


    BASIC Features:

    • Direct control of 3 motors in bidirectional and regulated mode up to 2,5A
    • Control of electric brake, fully proportional, brake deactivation when gear-up
    • Steering servo processor. Servo deactivation with gear-up activation
    • Small size and lightweight.

    Includes:

    • Two Main Retracts with 1/2" Trunion Lock.
    • One Nose Retract with 8mm Pin.
    • PL-LCG12 Basic Controller.
    • Three Male to Male Leads.
    • MPX Battery Connector.

    Demo Video of GENESIS Retracts installed in Boomerang Turbinator:

     



     

    Learn More
  8. Pro-Drive Gemini Electric Retract Set Basic
    $499.99
    Pro-Drive Gemini Electric Retract Set Basic

    Dreamworks is pleased to present our Pro-Drive electric retract systems. Over a year in development, our new electric series retracts and control modules are the most advanced electric gear systems available. Using our highly regarded Pro-Link retract units, we developed a strong and reliable drop-in electric drive actuator along with two distinct versions of our gear system control module.

    All the features of our Taurus Series with modified frames to provide a smaller footprint at the rails.

    The "Basic" system includes our durable T6 Gemini series retract frame and trunion, our Pro-Drive Gemini specific actuators and our exceptional "Basic" system control module. Our Basic system offers 3 gear cycling, fully proportional electric brake control (for use with our Pro-Brakes) and steering servo control. Intuitive programming makes setup a breeze.

    All Taurus Series Retracts are reversible!

     

    Includes

    • Three Pro-Drive Gemini Series Electric Retracts
    • Basic Control Module
    • Steering Tiller with 1/4" Pin
    • Three Male-Male Module to Rx Leads
    • Instruction Manual

    Specs:

    •     Length - 4.125" (105mm)
    •     Frame Width - .88" (22.3mm)
    •     Depth - 1.25" (31.75mm)
    •     Frame Rail mount length - 1.75" (44.45mm)
    •     Frame Rail Mount Width - 1.75" (44.45mm)
    •     90 Degree Extension

     

    • Cut Off Amperage - 1.5A
    • Operating Voltage - 6V to 10V
    • 5.25" long 3.1oz strut, weight loaded at the axle - Stall was achieved at 38oz (2.375lbs, 1077g)
    • 8" long 6oz strut, weight loaded at the axle - Stall was achieved at 17.3oz (1.08lbs, 490.44g)
    • Transit time is roughly 6 seconds.
    Learn More
  9. Pro-Drive Gemini Electric Retract Set PRO
    $539.99
    Pro-Drive Gemini Electric Retract Set PRO

    Dreamworks is pleased to present our Pro-Drive electric retract systems. Over a year in development, our new electric series retracts and control modules are the most advanced electric gear systems available. Using our highly regarded Pro-Link retract units, we developed a strong and reliable drop-in electric drive actuator along with two distinct versions of our gear system control module.

    All the features of our Taurus Series with modified frames to provide a smaller footprint at the rails.

    The "PRO" system includes our durable T6 Gemini series retract frame and trunion, our Pro-Drive Gemini specific actuators and our feature packed "PRO" system control module. Our PRO Control System offers a host of features over our "Basic" module.

    PRO Features:

    -Control by Single channel (Gear operation and brake operation combined on single channel) or separate channels for gear and brake.

    -Control 3 landing gears. Programmable independent delay for each gear in UP and DOWN sequence.

    -Control of electric brake:

    •  Proportional and adjustable maximum brake force
    •  Continuous operation or pulsed mode for "ABS" effect, 10 levels of pulse ratio.
    •  Brake Limiter to set max brake force

    -Control of steering servo

    • Allow to use same channel as the rudder despite different center, independant travel gain and direction on steering servo from rudder servo. The steering servo center, travel and sense of movement can be adjusted.
    • The steering servo is centered and deactived during gear operation and gear UP phase.

    -Door control output:

    • 3 independent servo outputs for door control.
    • Each output can be programmed in 3 different positions (Gear UP, Gear Down and Gear Moving phase).
    • Servo Switch-off. Door servos can be deactivated after movement to prevent the posibility of servo burnout on a jammed door. Deactivation time can be programmed.

    -Manual mode:

    • Provides the ability cycle the gear manually for testing during setup phase, movement can be stopped and reasumed in any position.
    • Each drive motor can be independently run in any direction and stopping in any position for checking clearance, etc.

    -Motor Log:

    • Cycle counter for scheduled maintenance.

    -Easy setup:  All adjustments are done through a Xicoy data terminal (not included).

    -Electronic switch for the main battery.

    Note:

    •  The unit can be programmed using the onboard LED and switch like our Basic controller (options limited using this program method)
    •  Data terminal for full programming not included. Compatible with all Xicoy SBus style data terminals used with Xicoy brand ECUS.

    All Taurus Series Retracts are reversible!

     

    Includes

    • Three Pro-Drive Gemini Series Electric Retracts
    • "PRO" Sequencing Control Module
    • Steering Tiller Assembly 1/4" Pin
    • Three Male-Male Module to Rx Leads
    • Instruction Manual

    Specs:

    •     Length - 4.125" (105mm)
    •     Frame Width - .88" (22.3mm)
    •     Depth - 1.25" (31.75mm)
    •     Frame Rail mount length - 1.75" (44.45mm)
    •     Frame Rail Mount Width - 1.75" (44.45mm)
    •     90 Degree Extension
    • 1/2" Trunion (1/2" Strut Mounting)
    • Cut Off Amperage - 1.5A
    • Operating Votage - 6V to 10V
    • 5.25" long 3.1oz strut, weight loaded at the axle - Stall was achieved at 38oz (2.375lbs, 1077g)
    • 8" long 6oz strut, weight loaded at the axle - Stall was achieved at 17.3oz (1.08lbs, 490.44g)
    • Transit time is roughly 6 seconds.
    Learn More
Desc

Items 1-9 of 39

View as Grid List
per page
To Top