SWITCHES

SWITCHES

SWITCHES & CHARGE JACKS

Desc

Items 1-9 of 62

View as Grid List
per page
  1. Advanced Radio Smart Bus Elite with Pin Switch
    $210.00
    Advanced Radio Smart Bus Elite with Pin Switch

    The Smart Bus is the complete power expansion system designed for the pilot who does not need servo voltage regulation. It comes with 12 inputs, 26 Outputs, active dual battery redundant, power distribution, battery monitoring, multi-point servo matching and a flight timer. Supplied with a vibrant 2.5 inch colour screen to monitor and program all these features. With Pin switching option.


    Sub-trim and reverse on all major outputs

    Ever spent hours, mechanically matching servos and never being able to get them just right or had to use a separate channel on your receiver, just to reverse a servo. With our intuitive and simple setup you can easily sub-trim at the centre and end-points of all your major outputs. Using Smart Bus you can individually reverse your servos at a touch of a button.


    12 inputs and 26 outputs.
    Looking at that next big project and wondering how you’re going to power all those servos, if you have enough channels on a receiver to power servos, retracts, flaps, brakes, ailerons, dual rudders, dual turbines or engines. With 26 outputs and up to 12 inputs, your system will always have more than enough outputs.


    Vibrant colour touch screen display.
    Gone are the days of fiddly buttons and frustrations, no more bind plugs and small screw drivers needed. The vibrant Smart Display gives you feedback and simple programming all in one touch screen display. With intuitive buttons and a single setup design. Your model will be in the air before you know it.


    Dual battery redundancy, power management you can trust.
    Ever wondered how many flights you have left before a charge, what about the health of your packs. Ensure that your model is safe and ready to fly with our dual battery redundancy technology. Using perfect diode technology, we link the batteries together, giving your model a powerful system capable of more flights before a recharge and with the addition of the Smart Screen you can directly monitor the voltage and milliamps used from you batteries. Models are expensive, ensure yours is in good condition to fly.

    Now you have a choice of dual switching options.

    Remote Fail Safe Power Switching. We all fly our models via remote control so why not power your model on and off remotely as well! Is it possible to accidentally switch my model off? The Advanced Radio fail safe Remote Switch system uses our propriety combination switching system and operates for a range of only 30 feet so you can rest at ease that you will not power off your model accidentally.

    Pin and Flag Fail Safe Power Switching. If you prefer the traditional method of switching then rest at ease Advanced Radio still offers the tried and proved fail safe method of switching.

    SPECIFICATIONS:

    • * Works with single or dual battery configuration.
    • * Works with all battery chemistries. LiFe. LiPo, Lion, NiMh, NiCD.
    • * Full Dual Battery Redundancy - If one battery fails the other battery takes full control.
    • * 2 x 100 amp independent circuits.
    • * Screen 2.4inch diagonal touch screen with 64k colour
    • * Screen case dimensions 3.4 x 2.0 x 0.5 inches (86 x 50 x 12)mm
    • * Smart Bus dimensions 4.2 x 3.0 x 0.9 inches (107 x 78 x 23)mm
    • *Vibrant Colour touch Screen
    • *Multi-match technology
    • *Optional optical ignition
    Learn More
  2. JetCentral BlueTooth Adapter Module
    $110.00
    JetCentral BlueTooth Adapter Module

    JetCentral BlueTooth Adapter Module


    Small and light weight bluetooth adapter to put your Hand Data Terminal on your phone or tablet, download the App for free from Google play.

    •     Weight: 5g
    •     Transmision range: 10 meters.
    •     Standby consumption: 55 mA
    •     Transmission consumption: 62mA
    •     Size: 22.8mm x 40.8mm
    •     Mobile App: Android
    Learn More
  3. AS1-K12, Armsafe Arming Kit, 12AWG
    $13.40
    AS1-K12, Armsafe Arming Kit, 12AWG

    This is the Schumacher ArmSafe Arming Kit with 12AWG Wiring.

    FEATURES:

    Reduces the risk of propeller strikes when installed between the
    battery and ESC in electric RC models

    INCLUDES:

    Aluminum Nut/Ring
    Female Ultra Plug
    Arming Plug
    Black Plastic Base
    18" (457mm) length of 12AWG Wire with Red Insulation
    2.7" (70mm) section of Shrink Tubing
    Mounting Hardware

    SPECIFICATIONS:

    12AWG Wire Current Capacity: 80A Continuous, 120A Max Burst
    Rated with 10mph 80° air flow for eight minutes with burst
    ratings for 5 seconds provided the average current (including
    the bursts) does not exceed the Max Continuous amperage rating

    Learn More
  4. Jeti Electronic Switch with Magnetic Key SPS 20
    $45.00
    Jeti Electronic Switch with Magnetic Key SPS 20

    Jeti Electronic Switch with Magnetic Key SPS 20

    The SPS 20 from Jeti is a single pole electronic switch operated with the included magnetic key. The advantage of an electronic switch is that it offers a virtual unlimited on/off cycle, unlike mechanically operated switches.

    For the first time ever, your models receiver system can be turned ON/OFF with a simple flip of the switch, wirelessly from the Jeti DC/DS transmitters. The R3/RSW receiver fully replaces Jeti Magnetic Switch which is widely used with Jeti Voltage Regulators as well as their Electronic Switches. Simply cut or unplug the existing switch (Install a Male JR type connector if needed), and connect your device to the #3 port of the R3/RSW receiver.

    The SPS 20 is designed for 3.5-14V input and supports up to 10A continuous current or 20A burst current for your connected devices. This unit is most suitable for today's high-voltage servos, which you might be operating directly from a two-cell LiFe battery or similar Li-Poly battery pack. Please note that SPS20 does not include a regulator. Output voltage is equal to input voltage. The output current is divided between the two sets of output wires, where each output supports a maximum of 5A continuous or 10A burst current.

    The unit features one set of input wires for your battery connection and two sets of output wires fitted with JR connectors to connect to your receiver or other device. The magnetic key/wand and faceplate are also included.

    The faceplate contains an integrated LED to indicate the on/off status of the switch. Should the battery become disconnected, the unit remembers its on/off state i.e. if the unit is switched on and the battery is disconnected, the unit will remain on when the battery is reconnected.

     

    • Model  SPS20
    • Operating Voltage  3.5-14V
    • Max Voltage  16V
    • Max Power  280W
    • Max Amp  10A Continues/20A Peak
    • Weight  31g
    • Dimensions  46mm x 24mm x 6.5mm
    Learn More
  5. Booma RC Smart Switch 2 JR In 2 JR Out
    $100.50
    Booma RC Smart Switch 2 JR In 2 JR Out

    Booma RC Smart Switch -  2 JR In 2 JR Out Connections.

    Dual Low Loss Battery Balancing and Redundancy Pin Flag Power Switch with colour touch screen. Ideal for all Scale models and Multi-Rotor craft.

    The next step in battery sharing technology

    Based off our proven hidden switch design, we have taken our battery sharing technology and added a touch screen display. With the new Battery Guard Technology you'll always know the state of your model.

    Designed with all batteries in mind

    With the release of the LiFe battery chemistry, battery monitoring is more important than ever. Want to check how much you have used since your last charge the Smart Switch will show you, using our Battery Guard Technology we track how much each pack has used since last charge. Designed to work with all new 2 cell chemistries (LiFe, LiPo and Li-ion) as well as some 5 cell packs (NiHM and NiCD).

    Simple one time setup

    Simply plug your batteries in, power up and use the touch smart screen to program the chemistry and capacity if your packs. The Battery Guard Technology does the rest. Need to know if your packs are ok. The smart switch gives you live battery voltage on both packs. Want to know how much you are using per flight. We have included a per flight counter. We even included a flight timer and counter. Never wonder how many flights that airframe has had. The smart switch will give you the live feedback.

    Simple Install and Setup

    Simulated Instrumentation

    Need that extra scale look for your model. The Smart Switch comes with preinstalled splash screens including instrumentation panels, an artificial horizon and even a copy of the IMAC patter for scale aerobatic aircraft. Give your model that extra flair. The Smart Switch has you covered.

    Simulated Cockpit Instrumentation

    Smart Switch works with any single or dual battery system. Works with battery chemistry and voltage range from 2.5v to 8.4v.

    Already have a power distribution system in place. The smart switch will work with any existing receiver and power distribution combination. Using our Pin Flag and Ultra Bright Blue LED which can be mount discretely on your scale model. The Pin Flag controls the internally mounted switch and battery redundancy circuit. The result - beautiful scale appearance with dual battery redundancy peace of mind.

    Proven time and time again

    With the release of the hidden switch, Advance Radio perfected battery sharing technology. This new balancing technology offers zero voltage drop battery balancing and redundancy which means it can handle huge loads without generating heat. This means your receiver and servos get all the power unlike conventional battery balancing which loses precious power as heat.

    Want a switch that offers complete dual battery balancing and redundancy with an ultra-small footprint for your scale model then look no further. The new Smart Switch with battery balancing from our sister company AR (Advanced Radio) is the answer.

    PACKAGE INCLUDES:

    1 x Live feedback touch screen Smart display

    1 x Pin Flag Switch with mounting hardware.

    1 x Ultra Bright Blue LED with mounting hardware.

    1 x Dual Battery Balancing power switch circuit with built in battery watch technology

    2 x sets of JR Input and JR Output connectors with 20AWG Wire


    SPECIFICATIONS:

    * Ultra low foot print for the best scale looks.

    * With built in Battery Guard Technology. The Smart Switch constantly monitors battery voltage and current draw.

    * Works with single or dual battery configuration.

    * Works with all battery chemistries. LiFe. LiPo, Lion, NiMh, NiCD. Battery voltage range can be from 4.8volts to 12 volts.

    * Smart Switch is capable of handling input voltages up to 12volts.

    * Minimal external Footprint - All you see on the outside of your model is a 3mm pin Flag socket and (if required) a ultra high bright Blue LED. The pin Flag controls the internal power switch and dual battery redundancy.

    * Full Dual Battery Redundancy - If one battery fails the other battery takes full control.

    * Maximum Battery Power Balancing – Using dual battery technology, The Smart Switch draws current proportionally from both batteries while moving both batteries to a complete load balance situation. This means you get the maximum capacity out of both batteries all the time.

    * 2 x 25 amp independent circuits. HS1 is 2 x 25amp circuits into a high power matching battery redundancy circuit. HS1 actually uses 4 x 50 amp rated FET circuits for battery power matching. We passively rate HS1 at 25amps (Instantaneous) per circuit.

    * Available as standard with JR In/Out, Futaba In/Out, Ultra In/Out, EC3 In/Out or XT60 In/Out combinations. In/Out power connections can be tailored to suit your connection requirements.

    * For higher current rating please select 18AWG or 16AWG connection cables.

    See attached PDF Below to download the SmartSwitch User Guide.

    Learn More
  6. Booma RC Smart Switch 2 Deans/Ultra In 2 Deans/Ultra Out
    $110.00
    Booma RC Smart Switch 2 Deans/Ultra In 2 Deans/Ultra Out

    Booma RC Smart Switch -  2 Deans/Ultra In 2 Deans/Ultra Out Connections.

    Dual Low Loss Battery Balancing and Redundancy Pin Flag Power Switch with colour touch screen. Ideal for all Scale models and Multi-Rotor craft.

    The next step in battery sharing technology

    Based off our proven hidden switch design, we have taken our battery sharing technology and added a touch screen display. With the new Battery Guard Technology you'll always know the state of your model.

    Designed with all batteries in mind

    With the release of the LiFe battery chemistry, battery monitoring is more important than ever. Want to check how much you have used since your last charge the Smart Switch will show you, using our Battery Guard Technology we track how much each pack has used since last charge. Designed to work with all new 2 cell chemistries (LiFe, LiPo and Li-ion) as well as some 5 cell packs (NiHM and NiCD).

    Simple one time setup

    Simply plug your batteries in, power up and use the touch smart screen to program the chemistry and capacity if your packs. The Battery Guard Technology does the rest. Need to know if your packs are ok. The smart switch gives you live battery voltage on both packs. Want to know how much you are using per flight. We have included a per flight counter. We even included a flight timer and counter. Never wonder how many flights that airframe has had. The smart switch will give you the live feedback.

    Simple Install and Setup

    Simulated Instrumentation

    Need that extra scale look for your model. The Smart Switch comes with preinstalled splash screens including instrumentation panels, an artificial horizon and even a copy of the IMAC patter for scale aerobatic aircraft. Give your model that extra flair. The Smart Switch has you covered.

    Simulated Cockpit Instrumentation

    Smart Switch works with any single or dual battery system. Works with battery chemistry and voltage range from 2.5v to 8.4v.

    Already have a power distribution system in place. The smart switch will work with any existing receiver and power distribution combination. Using our Pin Flag and Ultra Bright Blue LED which can be mount discretely on your scale model. The Pin Flag controls the internally mounted switch and battery redundancy circuit. The result - beautiful scale appearance with dual battery redundancy peace of mind.

    Proven time and time again

    With the release of the hidden switch, Advance Radio perfected battery sharing technology. This new balancing technology offers zero voltage drop battery balancing and redundancy which means it can handle huge loads without generating heat. This means your receiver and servos get all the power unlike conventional battery balancing which loses precious power as heat.

    Want a switch that offers complete dual battery balancing and redundancy with an ultra-small footprint for your scale model then look no further. The new Smart Switch with battery balancing from our sister company AR (Advanced Radio) is the answer.

    PACKAGE INCLUDES:

    1 x Live feedback touch screen Smart display

    1 x Pin Flag Switch with mounting hardware.

    1 x Ultra Bright Blue LED with mounting hardware.

    1 x Dual Battery Balancing power switch circuit with built in battery watch technology

    2 x sets of Deans/Ultra Input and Deans/Ultra Output connectors with 20AWG WIre.


    SPECIFICATIONS:

    * Ultra low foot print for the best scale looks.

    * With built in Battery Guard Technology. The Smart Switch constantly monitors battery voltage and current draw.

    * Works with single or dual battery configuration.

    * Works with all battery chemistries. LiFe. LiPo, Lion, NiMh, NiCD. Battery voltage range can be from 4.8volts to 12 volts.

    * Smart Switch is capable of handling input voltages up to 12volts.

    * Minimal external Footprint - All you see on the outside of your model is a 3mm pin Flag socket and (if required) a ultra high bright Blue LED. The pin Flag controls the internal power switch and dual battery redundancy.

    * Full Dual Battery Redundancy - If one battery fails the other battery takes full control.

    * Maximum Battery Power Balancing – Using dual battery technology, The Smart Switch draws current proportionally from both batteries while moving both batteries to a complete load balance situation. This means you get the maximum capacity out of both batteries all the time.

    * 2 x 25 amp independent circuits. HS1 is 2 x 25amp circuits into a high power matching battery redundancy circuit. HS1 actually uses 4 x 50 amp rated FET circuits for battery power matching. We passively rate HS1 at 25amps (Instantaneous) per circuit.

    * Available as standard with JR In/Out, Futaba In/Out, Ultra In/Out, EC3 In/Out or XT60 In/Out combinations. In/Out power connections can be tailored to suit your connection requirements.

    * For higher current rating please select 18AWG or 16AWG connection cables.

    See attached PDF Below to download the SmartSwitch User Guide.

    Learn More
  7. Booma RC Intelliswitch Version 3 ULTRA Deans IN JR OUT
    $100.00
    Booma RC Intelliswitch Version 3 ULTRA Deans IN JR OUT

    Booma RC Intelliswitch Version 3 ULTRA Deans Style IN JR OUT Connectors

    Intelliswitch Version 3 with Active Battery Redundancy & Consumption Monitoring

    Digital Intelligent Switch with built in Active Battery Redundancy, Battery Balancing, Dual Battery Voltage Monitor, Dual Battery mA Usage Monitor, Flight Timer, Flight Counter and Temperature monitor.

    The newest addition to the world's most Intelligent Digital Switch for Radio Controlled models and Robotics.

    Intelliswitch V3 is the next generation in Intelligent monitoring and switching for giant scale RC and Robotics enthusiasts by a giant scale RC and Robotics enthusiast.

    Intelliswitch V3 offers all the features of Intelliswitch 2 with added Active battery monitoring and battery balancing as well as triple the current handing capabilities. All this in a compact, light weight and affordable package. Now you can protect your valuable model with Intelliswitch.

    Intelliswitch Version 3 Features:

    •     Microprocessor control - of 2 x independent high powered digital switching circuits.
    •     Fail Safe Switching of both batteries.
    •     NEW Active Battery Redundancy - if one battery fails the other battery takes over.
    •     NEW Active Battery Balancing - batteries packs are load balanced so you get the most power out of your dual batteries. If one pack has more power available then it will be given priority for usage. Once the packs are matched then power is drawn equally from both packs.
    •     Battery Voltage Monitoring of each battery.
    •     NEW Lowest Battery Voltage since last battery connection
    •     Battery Consumption of each battery in mA.
    •     Temperature of the internal components.
    •     Time of Last Flight or usage time.
    •     Built in Flight Log - Displays the number of flights on your models frame.
    •     Selectable Battery Type - for monitoring of LifeP04, LiPo and Lion battery chemistries.
    •     Low Voltage Alarm via LCD indication.
    •     2 x 20 Amp constant current capability (depending on connection cable configuration).
    •     2 x 35 Amp for 30 seconds.
    •     Calibration Algorithm for accurate current consumption monitoring.
    •     Micro-Power design low power usage in standby mode.
    •     Input Voltage 6v to 12v.
    •     Weight 28 grams.
    •     Dimensions 56mm x 22.8mm (2.2 x 0.9 inches).

    2 x Ultra Input / 2 x JR Output connectors

    Watch a sample of some of the prototype vibration tests for Intelliswitch and Wallaby Switch

     

    Learn More
  8. Jeti Electronic Switch Replacement Magnetic Key
    $9.00
    Jeti Electronic Switch Replacement Magnetic Key

    Jeti Electronic Switch Replacement Magnetic Key

     

    Learn More
  9. Jeti Magnetic Switch Universal 4-Port
    $39.00
    Jeti Magnetic Switch Universal 4-Port

    The Universal Magnetic Switch from Jeti is a dual pole electronic switch with four outputs operated with the magnetic key (Sold Separately). The advantage of an electronic switch is that it offers a virtual unlimited ON/OFF cycle, unlike mechanically operated switches.

    The Universal Magnetic Switch is designed for 3.5V - 59V input and supports up to four (4) individual devices connected to the ports. Output ports are divided to Master and OPTO, both sets of ports are optically insulated from each other preventing RF interference. Each pair of the connectors has single standard and single inverted output, this setup enables you to connect and control simultaneously several Jeti devices.

    The faceplate contains an integrated LED to indicate the ON/OFF status of the switch. Should one the devices become disconnected from the switch, the device will stay ON and switch will remember its ON/OFF state.

    Note: The Magnetic Key is Sold Seperatley. (See #JETI-SWMKEY)

    Learn More
Desc

Items 1-9 of 62

View as Grid List
per page
To Top