AFTERBURNER

AFTERBURNER
Desc

Items 1-9 of 18

View as Grid List
per page
  1. UniLight Afterburner Ring 76mm, 1300+ Lumen
    $125.00
    UniLight Afterburner Ring 76mm, 1300+ Lumen

    Afterburner Ring 76mm, 1300+ Lumen

    Our Ultra-Power afterburner rings are the first thrust nozzles based on emitter technology in the market. Specially manufactured aluminium core PCBs for this application is what makes the assembly of the high-performance emitters and the required heat dissipation possible. In addition, one cooling duct behind every emitter is adhered to dissipate enough heat during operation. Without any furhter air cooling, the rings can be operated permanently ca. 1-2 minutes and therefore, the mixing to the gas channel should only happen in the upper section.

    The light output of the emitter rings is gigantic high and even in an area of >120° to all ring sides visible. Thus, it will both directly shine into the outlet and into the nozzle, which strengthens tremendously the effect of a glowing pushing rod.

    Direct operation with 2S (8V) Lipo. Please ensure sufficient cooling air during operation. The high power requirement of the afterburner rings requires sufficiently dimensioned batteries and an efficient control. Please see our recommended modules.

    Pay close attention to input voltage as Control Modules can handle increased voltage and do not regulate output to the Afterburner Ring.

    This ring is delivered with two 1m/0.5mm silicon cables. These cables can be plugged in parallel into the control. A boost effect can be created when using 2-Channel controls in order to operate the afterburner ring in the maximum operation mode with the highest performance via both cables. For a better light distribution, you can use our nozzle attachments under the rubric accessories.

    Technical Data

    Performance: 18 emitters with 60-90 Lumen
    Voltage: 2S/8V
    Electricity: 2.5-3.5A
    Beam angle: ~100°
    Internal Dimension: 76.2mm
    External dimension: 90mm
    Weight: 40g (without cable)
    Delivery: ready to use with 1m connection cable for 2S LiPo operation

     


    With the X2 technique high power LEDs are operated in a "cluster". These achieve double the light output for the same heat or the same light output at half heat dissipation. Yet our X2 lights are still fully compatible with all our other lamps. If X2 lights, such as spotlights, are supplied with separate cables, these cables must be used in the delivered wiring! X2 lights are reacting more strongly on a weakening battery.


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  2. UniLight Afterburner Ring 60mm, 1150+ Lumen
    $105.00
    UniLight Afterburner Ring 60mm, 1150+ Lumen

    Afterburner Ring 60mm, 1150+ Lumen

    Our Ultra-Power afterburner rings are the first thrust nozzles based on emitter technology in the market. Specially manufactured aluminium core PCBs for this application is what makes the assembly of the high-performance emitters and the required heat dissipation possible. In addition, one cooling duct behind every emitter is adhered to dissipate enough heat during operation. Without any furhter air cooling, the rings can be operated permanently ca. 1-2 minutes and therefore, the mixing to the gas channel should only happen in the upper section.

    The light output of the emitter rings is gigantic high and even in an area of >120° to all ring sides visible. Thus, it will both directly shine into the outlet and into the nozzle, which strengthens tremendously the effect of a glowing pushing rod.

    Direct operation with 2S (8V) Lipo. Please ensure sufficient cooling air during operation. The high power requirement of the afterburner rings requires sufficiently dimensioned batteries and an efficient control. Please see our recommended modules.

    Pay close attention to input voltage as Control Modules can handle increased voltage and do not regulate output to the Afterburner Ring.

    This ring is delivered with two 1m/0.5mm silicon cables. These cables can be plugged in parallel into the control. A boost effect can be created when using 2-Channel controls in order to operate the afterburner ring in the maximum operation mode with the highest performance via both cables. For a better light distribution, you can use our nozzle attachments under the rubric accessories.

    Technical Data

    Performance: 15 emitters with 60-90 Lumen
    Voltage: 2S/8V
    Electricity: 2-2.5A
    Beam angle: ~100°
    Internal Dimension: 60mm
    External dimension: 73.8mm
    Weight: 33g (without cable)
    Delivery: ready to use with 1m connection cable for 2S LiPo operation


    With the X2 technique high power LEDs are operated in a "cluster". These achieve double the light output for the same heat or the same light output at half heat dissipation. Yet our X2 lights are still fully compatible with all our other lamps. If X2 lights, such as spotlights, are supplied with separate cables, these cables must be used in the delivered wiring! X2 lights are reacting more strongly on a weakening battery.


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  3. UniLight Afterburner Ring Replacement Cooler (Heatsink)
    $18.95
    UniLight Afterburner Ring Replacement Cooler (Heatsink)

    UniLight Afterburner Ring Replacement Cooler (Heatsink)

    Cooling ducts for our afterburner rings as spare parts or for expanding the RINGX-Series.

    • External dimension:D7x25mm
    • Weight: 14g (10 pieces)
    Learn More
  4. UniLight Afterburner Ring 141mm, 2500+ Lumen
    $250.00
    UniLight Afterburner Ring 141mm, 2500+ Lumen

    Afterburner Ring 141mm, 2500+ Lumen

    Our Ultra-Power afterburner rings are the first thrust nozzles based on emitter technology in the market. Specially manufactured aluminium core PCBs for this application is what makes the assembly of the high-performance emitters and the required heat dissipation possible. In addition, one cooling duct behind every emitter is adhered to dissipate enough heat during operation. Without any furhter air cooling, the rings can be operated permanently ca. 1-2 minutes and therefore, the mixing to the gas channel should only happen in the upper section.

    The light output of the emitter rings is gigantic high and even in an area of >120° to all ring sides visible. Thus, it will both directly shine into the outlet and into the nozzle, which strengthens tremendously the effect of a glowing pushing rod.

    Direct operation with 2S (8V) Lipo. Please ensure sufficient cooling air during operation. The high power requirement of the afterburner rings requires sufficiently dimensioned batteries and an efficient control. Please see our recommended modules.

    Pay close attention to input voltage as Control Modules can handle increased voltage and do not regulate output to the Afterburner Ring.

    This ring is delivered with two 1m/0.5mm silicon cables. These cables can be plugged in parallel into the control. A boost effect can be created when using 2-Channel controls in order to operate the afterburner ring in the maximum operation mode with the highest performance via both cables. For a better light distribution, you can use our nozzle attachments under the rubric accessories.

    Technical Data

    Performance: 39 emitters with 60-90 Lumen
    Voltage: 2S/8V
    Electricity: 6-7A
    Beam angle: ~100°
    Internal Dimension: 141mm
    External dimension: 154mm
    Weight: 85g (without cable)
    Delivery: ready to use with 2x1m connection cable for 2S LiPo operation


    With the X2 technique high power LEDs are operated in a "cluster". These achieve double the light output for the same heat or the same light output at half heat dissipation. Yet our X2 lights are still fully compatible with all our other lamps. If X2 lights, such as spotlights, are supplied with separate cables, these cables must be used in the delivered wiring! X2 lights are reacting more strongly on a weakening battery.


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  5. UniLight Light-Spreader Nozzle, 3D 92mm
    $28.00
    UniLight Light-Spreader Nozzle, 3D 92mm

    Light-Spreader Nozzle, 3D for 92mm Afterburner Ring

    Evenly diffuses the led's.

    Although the enormous light output of the emitter allows the individual illuminated dots to melt rapidly. Through the translucent 3D printed ring attachment the harsh light of the afterburner rings is strongly refracted and distributed over the surface. The attachment shape is inspired by a Nozzle and produces a glaring element instead of a flat ring.

    Weight: 13g

    Learn More
  6. UniLight Light-Spreader Nozzle, 3D 76mm
    $27.00
    UniLight Light-Spreader Nozzle, 3D 76mm

    Light-Spreader Nozzle, 3D for 76mm Afterburner Ring

    Evenly diffuses the led's.

    Although the enormous light output of the emitter allows the individual illuminated dots to melt rapidly. Through the translucent 3D printed ring attachment the harsh light of the afterburner rings is strongly refracted and distributed over the surface. The attachment shape is inspired by a Nozzle and produces a glaring element instead of a flat ring.

    Weight: 11g

    Learn More
  7. UniLight Light-Spreader Nozzle, 3D 60mm
    $24.00
    UniLight Light-Spreader Nozzle, 3D 60mm

    Light-Spreader Nozzle, 3D for 60mm Afterburner Ring

    Evenly diffuses the led's.

    Although the enormous light output of the emitter allows the individual illuminated dots to melt rapidly. Through the translucent 3D printed ring attachment the harsh light of the afterburner rings is strongly refracted and distributed over the surface. The attachment shape is inspired by a Nozzle and produces a glaring element instead of a flat ring.

    Weight: 9g

    Learn More
  8. UniLight Afterburner Ring 125mm, 2500+ Lumen
    $209.00
    UniLight Afterburner Ring 125mm, 2500+ Lumen

    Afterburner Ring 125mm, 2500+ Lumen

    Our Ultra-Power afterburner rings are the first thrust nozzles based on emitter technology in the market. Specially manufactured aluminium core PCBs for this application is what makes the assembly of the high-performance emitters and the required heat dissipation possible. In addition, one cooling duct behind every emitter is adhered to dissipate enough heat during operation. Without any furhter air cooling, the rings can be operated permanently ca. 1-2 minutes and therefore, the mixing to the gas channel should only happen in the upper section.

    The light output of the emitter rings is gigantic high and even in an area of >120° to all ring sides visible. Thus, it will both directly shine into the outlet and into the nozzle, which strengthens tremendously the effect of a glowing pushing rod.

    Direct operation with 2S (8V) Lipo. Please ensure sufficient cooling air during operation. The high power requirement of the afterburner rings requires sufficiently dimensioned batteries and an efficient control. Please see our recommended modules.

    Pay close attention to input voltage as Control Modules can handle increased voltage and do not regulate output to the Afterburner Ring.

    This ring is delivered with two 1m/0.5mm silicon cables. These cables can be plugged in parallel into the control. A boost effect can be created when using 2-Channel controls in order to operate the afterburner ring in the maximum operation mode with the highest performance via both cables. For a better light distribution, you can use our nozzle attachments under the rubric accessories.

    Technical Data

    Performance: 33 emitters with 60-90 Lumen
    Voltage: 2S/8V
    Electricity: 4.5-5.5A
    Beam angle: ~100°
    Internal Dimension: 124.8mm
    External dimension: 138.6mm
    Weight: 69g (without cable)
    Delivery: ready to use with 2x1m connection cable for 2S LiPo operation


    With the X2 technique high power LEDs are operated in a "cluster". These achieve double the light output for the same heat or the same light output at half heat dissipation. Yet our X2 lights are still fully compatible with all our other lamps. If X2 lights, such as spotlights, are supplied with separate cables, these cables must be used in the delivered wiring! X2 lights are reacting more strongly on a weakening battery.


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  9. UniLight Afterburner Ring 92mm, 1800+ Lumen
    $157.00
    UniLight Afterburner Ring 92mm, 1800+ Lumen

    Afterburner Ring 92mm, 1800+ Lumen

    Our Ultra-Power afterburner rings are the first thrust nozzles based on emitter technology in the market. Specially manufactured aluminium core PCBs for this application is what makes the assembly of the high-performance emitters and the required heat dissipation possible. In addition, one cooling duct behind every emitter is adhered to dissipate enough heat during operation. Without any furhter air cooling, the rings can be operated permanently ca. 1-2 minutes and therefore, the mixing to the gas channel should only happen in the upper section.

    The light output of the emitter rings is gigantic high and even in an area of >120° to all ring sides visible. Thus, it will both directly shine into the outlet and into the nozzle, which strengthens tremendously the effect of a glowing pushing rod.

    Direct operation with 2S (8V) Lipo. Please ensure sufficient cooling air during operation. The high power requirement of the afterburner rings requires sufficiently dimensioned batteries and an efficient control. Please see our recommended modules.

    Pay close attention to input voltage as Control Modules can handle increased voltage and do not regulate output to the Afterburner Ring.

    This ring is delivered with two 1m/0.5mm silicon cables. These cables can be plugged in parallel into the control. A boost effect can be created when using 2-Channel controls in order to operate the afterburner ring in the maximum operation mode with the highest performance via both cables. For a better light distribution, you can use our nozzle attachments under the rubric accessories.

    Technical Data

    Performance: 24 emitters with 60-90 Lumen
    Voltage: 2S/8V
    Electricity: 3.5-4A
    Beam angle: ~100°
    Internal Dimension: 92.4mm
    External dimension: 106.2mm
    Weight: 50g (without cable)
    Delivery: ready to use with 2x1m connection cable for 2S LiPo operation


    With the X2 technique high power LEDs are operated in a "cluster". These achieve double the light output for the same heat or the same light output at half heat dissipation. Yet our X2 lights are still fully compatible with all our other lamps. If X2 lights, such as spotlights, are supplied with separate cables, these cables must be used in the delivered wiring! X2 lights are reacting more strongly on a weakening battery.


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
Desc

Items 1-9 of 18

View as Grid List
per page
To Top