LIGHTS

LIGHTS
Desc

Items 1-9 of 78

View as Grid List
per page
  1. UniLight 5mm High-Eff-LED, 0.3W White with Reflector
    $7.50
    UniLight 5mm High-Eff-LED, 0.3W White with Reflector

    High-performance 5mm-LED in WHITE with plug-in reflector

    These small LEDs have an enormous luminosity with a relatively wide beam angle and represent today's highest technical efficiency for these LED types. The luminaire gets hardly hot, it only needs a few milliamperes and is ideal for use in smaller models like helicopters and styrofoam models (up to about 1m). It's also suitable for night flights. It can be used as position light or spotlight through the plug-in reflector.

    Technical Data

    • Electricity: 0.3W reference power, 6-12V, 0.03A
    • Beam angle: ~25°
    • Light intensity: 27000mcd, ca. 4 Lumen
    • Dimension: D5x10mm (without cable)
    • Weight: 2g (without cable)
    • Delivery: 1m connection cable included and series resistor for operation 6-12V


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  2. UniLight 16Wx2 Strobe / Flashlight, 11mm, SHORT, T-Fuse Green
    $34.00
    UniLight 16Wx2 Strobe / Flashlight, 11mm, SHORT, T-Fuse Green

    16Wx2 flash, 11mm, SHORT, T-Fuse Green

    Powerful flashlight in x2 technology - extreme light output! The profile of 11mm light series is externally very slim design and fits optically to smaller models. By x2 performance especially for large models a real eye-catcher. This light only suitable for short flash or flashing mode. To ensure the operational safety of light and model, is located on the underside of the unit an overtemperature protection. If the lamp thus operated for too long and thus become too hot, this switch will turn off the light. To increase the service life of this function must not be used permanently!

    The luminaire is fully assembled for use with 2S LiPo (about 8V). Check after installation the operating temperatures.

    Technical Specifications:

    Electrical: 16Wx2 reference power, 8 (12) V, 1.4A
    Angle:> 160 °
    Aperture: 2x200 Lumens RED
    Aperture: 2x400 lumens WHITE
    Dimensional light cap: 11.5x42.5x10mm until 4mm sunk without loss of the radiation angle
    Overall dimensions: 11.5x70x10mm
    Weight: 8g (without cable)
    Delivery: with 1m silicone cable and pre-assembled ready for 2S resistor operations

    With the X2 technique high power LEDs are operated in a "cluster". These achieve double the light output for the same heat or the same light output at half heat dissipation. Yet our X2 lights are still fully compatible with all our other lamps. If X2 lights, such as spotlights, are supplied with separate cables, these cables must be used in the delivered wiring! X2 lights are reacting more strongly on a weakening battery.


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  3. UniLight 8Wx2 Ultra-Power SLIM, 10mm Green Beacan or ACL
    $34.00
    UniLight 8Wx2 Ultra-Power SLIM, 10mm Green Beacan or ACL

    8Wx2 Ultra-Power SLIM, 10mm, T-Fuse Green

    Thin high-performance light with 8Wx2 and wide beam angle through a special spreading cap. The slim light is delivered as a ready assembled unit on a special, CNC manufactured aluminium tube and a permanently mounted polycarbonate cap as covering. The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use a 8W-3S adaption cable.

    Additionally, the scope of delivery contains another cap of polycarbonate, which transforms the luminaire into a profiled/drop-shaped outside light. The cap can be sperartely glued in and individually varnished in the model colour.

    Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These 8W luminaires are not suitable for continuous operation without additional cooling, operation times of a few minutes are possible. Please check operation temperatures. The luminaires are perfectly suited to be BEACON or ACL lights. The integrated temperature sensor will switch off the light in case of overheating, thus the useage as powerful position light is possible.

    Technical Data

    Electricity: 8W reference power, 8(12)V, 0.7A
    Beam angle: >160°
    Light intensity: ~200 Lumen RED
    Light intensity: ~300 Lumen GREEN
    Light intensity: ~400 Lumen WHITE
    Dimension cooling tube: D10x45mm, flange D12mm
    Dimension light cap: D10x12.5mm, flange for carrier D12mm
    Total mass: D10/12mm, 57.5mm length
    Weight: 5g (without cable)
    Delivery: ready to use with 1m silicon cable and series resistor for 2S, resistor for 3S enclosed, profiled expansion cap

    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  4. UniLight 4W Universal Short Pure Light Green
    $15.00
    UniLight 4W Universal Short Pure Light Green

    4W PURE light, short - GREEN

    Universal STROBE light for installation behind existing glass cap, mostly on wingtips or on the leading edge or special DIY solutions. The module is being delivered completely prewired on an aluminium heatsink.

    Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. In delivery state, these lamps are only suitable for normal operation from 5 to 10 minutes when paying attention to a slight air flow. Please check operation temperatures after installation and ensure sufficient air cooling.

    Technical Data:

    Electricity: 4W reference power, 8(12)V, 0.35A
    Beam angle: ~160°
    Light intensity: ~50 Lumen RED
    Light intensity: ~70 Lumen GREEN
    Light intensity: ~100 Lumen WHITE
    Dimension bolt : D7x15mm
    Dimension chip: D8mm
    Weight: 2g (without cable)
    Delivery: ready to use with 1m connection cable and series resistor for 2S, resistor for 3S enclosed, mounting screws

    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  5. UniLight 5mm Navigation & Strobe, 10Wx2 Green/White
    $40.00
    UniLight 5mm Navigation & Strobe, 10Wx2 Green/White

    UniLight 5mm Navigation & Strobe, 10Wx2 - GREEN/WHITE


    Extremely slim but powerful miniature position and flashlight in one housing. The 5mm lightbar outside very slim and fits optically on kleinse models, thin airfoil and Eigent Perfect for all sports models. but by the new LED emitter has an extremely light and flash output despite the micro-dimension and is therefore also suitable for larger models. The novel, shifted inward cooling surface allows astonishingly compact dimensions with unique slim design.

    The luminaire is fully assembled for use with 2S Lipo (about 8V). During operation with 3S (12V) of the supplied resistor must be used. Please note that high power LEDs can be very hot, up to 70 ° C is quite normal. These lamps with heatsink enclosures are suitable for model aircraft operation when an air flow is possible (in flight). If this is not the case, then switched-on durations of 5-10 should not be exceeded. Check after installation the operating temperatures.

    Technical specifications

    • Electrical: 2Wx2 RED / GREEN and WHITE 8Wx2 reference power, 8 (12) V
    • Angle:> 150 °
    • Aperture: ~ 80 lumens RED
    • Aperture: ~ 140 lumens GREEN
    • Aperture: ~ 450 lumens WHITE
    • Dimensions: 38x5x4mm
    • Dimensions cooling surface: 30x15x4 (min. 2 heatsink use)
    • Weight: 3g (without cable) Weight: (without cord)
    • Delivery: enclosed with 2x0.5m Teflon cable and a pre-prepared series resistor for 2S, 3S for resistance


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  6. UniLight 5mm Navigation & Strobe, 10Wx2 Red/White
    $40.00
    UniLight 5mm Navigation & Strobe, 10Wx2 Red/White

    UniLight 5mm Navigation & Strobe, 10Wx2 - RED/WHITE


    Extremely slim but powerful miniature position and flashlight in one housing. The 5mm lightbar outside very slim and fits optically on kleinse models, thin airfoil and Eigent Perfect for all sports models. but by the new LED emitter has an extremely light and flash output despite the micro-dimension and is therefore also suitable for larger models. The novel, shifted inward cooling surface allows astonishingly compact dimensions with unique slim design.

    The luminaire is fully assembled for use with 2S Lipo (about 8V). During operation with 3S (12V) of the supplied resistor must be used. Please note that high power LEDs can be very hot, up to 70 ° C is quite normal. These lamps with heatsink enclosures are suitable for model aircraft operation when an air flow is possible (in flight). If this is not the case, then switched-on durations of 5-10 should not be exceeded. Check after installation the operating temperatures.

    Technical specifications

    • Electrical: 2Wx2 RED / GREEN and WHITE 8Wx2 reference power, 8 (12) V
    • Angle:> 150 °
    • Aperture: ~ 80 lumens RED
    • Aperture: ~ 140 lumens GREEN
    • Aperture: ~ 450 lumens WHITE
    • Dimensions: 38x5x4mm
    • Dimensions cooling surface: 30x15x4 (min. 2 heatsink use)
    • Weight: 3g (without cable) Weight: (without cord)
    • Delivery: enclosed with 2x0.5m Teflon cable and a pre-prepared series resistor for 2S, 3S for resistance


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
  7. UniLight 3Wx2 Navigation & Strobe, Short, 7mm Red/White
    $23.00
    UniLight 3Wx2 Navigation & Strobe, Short, 7mm Red/White

    3Wx2 Navigation & Strobe, Short, 7mm Red/White

    Thumbnail positioning and flashlight in one housing. The profile light 7mm series is externally very slim and fits optically on kleinse models. But through thanks to new LED emitter has a high light output despite the micro-dimension, the compact design permits operation even on the smallest models. The novel, shifted inwards cooling surface allows astonishingly compact dimensions with unique slim design.

    The luminaire is fully assembled for use with 2S LiPo (about 8V). During operation with 3S (12V) of the enclosed resistor must be used. Please note that high-power LEDs can be very warm, up to 70 ° C is quite normal. These luminaires with heatsink enclosures are suitable for the model operations when an air flow is possible (in flight). If this is not the case, then switched-on durations of 5-10 should not be exceeded. Check after installation the operating temperatures.
    Technical specifications

    Electrical: 1wx2 RED / GREEN and WHITE 2Wx2 reference power, 8 (12) V
    Angle:> 150 °
    Aperture: ~ 40 lumens RED, 0.12A
    Aperture: ~ 50 lumens GREEN, 0.12A
    Aperture: ~ 110 lumens WHITE, 0.17A
    Dimension Cap: 19x8x6
    Dimensions cooling pin: D7x15
    Weight: (without cable)
    Delivery: enclosed with 2x0.5m Teflon cable and pre-assembled ready for 2S series resistance, resistance for 3S

    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

     

    Learn More
  8. UniLight 3Wx2 Navigation & Strobe, Short, 7mm Green/White
    $23.00
    UniLight 3Wx2 Navigation & Strobe, Short, 7mm Green/White

    3Wx2 Navigation & Strobe, Short, 7mm Green/White

    Thumbnail positioning and flashlight in one housing. The profile light 7mm series is externally very slim and fits optically on kleinse models. But through thanks to new LED emitter has a high light output despite the micro-dimension, the compact design permits operation even on the smallest models. The novel, shifted inwards cooling surface allows astonishingly compact dimensions with unique slim design.

    The luminaire is fully assembled for use with 2S LiPo (about 8V). During operation with 3S (12V) of the enclosed resistor must be used. Please note that high-power LEDs can be very warm, up to 70 ° C is quite normal. These luminaires with heatsink enclosures are suitable for the model operations when an air flow is possible (in flight). If this is not the case, then switched-on durations of 5-10 should not be exceeded. Check after installation the operating temperatures.
    Technical specifications

    Electrical: 1wx2 RED / GREEN and WHITE 2Wx2 reference power, 8 (12) V
    Angle:> 150 °
    Aperture: ~ 40 lumens RED, 0.12A
    Aperture: ~ 50 lumens GREEN, 0.12A
    Aperture: ~ 110 lumens WHITE, 0.17A
    Dimension Cap: 19x8x6
    Dimensions cooling pin: D7x15
    Weight: (without cable)
    Delivery: enclosed with 2x0.5m Teflon cable and pre-assembled ready for 2S series resistance, resistance for 3S

    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

     

    Learn More
  9. UniLight 8Wx2 universal STROBE, 24mm White
    $39.00
    UniLight 8Wx2 universal STROBE, 24mm White

    8Wx2 universal DOUBLE-BEACON, 10mm, T-Fuse

    High power light with two 8Wx2 reference power and wide radiation angle. The lights are controlled seperately and can be used as rotating beacon or parallel as ultra high power strobe. The light is delivered with several radiation caps for individual usage:

    1x 24mm ROUND
    1x 24mm PROFILE

    The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use two 8W-3S adaption cable.

    Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These 8W luminaires are not suitable for continuous operation without additional cooling, operation times of a few minutes are possible. Please check operation temperatures. The luminaires are perfectly suited to be BEACON or ACL lights. The integrated temperature sensor will switch off the light in case of overheating.

    Technical Data

    Electricity: 8W reference power, 8(12)V, 2x0.7A
    Beam angle: >160°
    Light intensity: 2x~200 Lumen RED
    Light intensity: 2x~400 Lumen WHITE
    Dimension: 24x20x20mm
    Weight: 6g (without cable)
    Delivery: ready to use with 1m silicon cable and series resistor for 2S, resistor for 3S enclosed


    The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

    Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

    Note: The LED lights are extremely bright! Never look directly into a LED!

    Learn More
Desc

Items 1-9 of 78

View as Grid List
per page
To Top